It’s a carve up

Martin Bell on how to take corners with ease.
  
  


Carved turns have been used by ski-racers for decades as the most efficient way of getting through racecourses. But in the mid-90s, the introduction of curvier-shaped "carving skis" made carving accessible to all. Nowadays, "carving skis" are simply known as "skis" - because they're the only kind that are available.

Of course, it was always possible to carve turns with the old "straight skis", but it required huge leg strength to generate the enormous pressure necessary to bend them into the right curved shape for carving. This shape was called "reverse camber". Now, when one of the modern, hourglass-shaped skis is tilted over on to its edge, there is a large gap between the ground and the ski, just under the binding. Then, all the skier needs to do is to gently pressurise the ski by standing on it; the gap will close, and the ski will bend easily into reverse camber.

There are many benefits for non-racing skiers who learn to carve. First and foremost, it's more fun! A carved turn will glide you around a corner without any loss of speed, whereas a skidded turn (the opposite of carving) will always slow you down. Secondly, a carved turn can increase your efficiency in getting around the mountain: if you're facing a sharp turn followed by a long flat, a carved turn will help you to carry more speed and cut down on skating and poling. Thirdly, a carving ski is much more stable than a skidding one, and will slice its way across icy patches like a train on rails.

The best introduction to carving is to traverse across the hill, with your downhill ski well tilted on to its uphill edge, and with your upper body leaning well out over that downhill ski. A wide stance will help with this exercise. As you set off, your downhill ski will track along its edge, and start to carve uphill - if you can manage this, congratulations! You have already performed part of a carved turn. The next exercise, still working in a traverse across the hill, is to try alternating between sideslipping down the hill and carving across it. This will teach you how to go intentionally from skidding to carving (and vice versa).

Soon, you'll be ready to carve an entire turn. You must choose extremely flat terrain for this, because a carved turn will not kill off any of your speed. Just tilt your outside ski on to its edge, lean out over it with your upper body, and set off. You must be patient and wait for the ski to carve around of its own accord. The most common mistake is to try to pivot the ski around with your foot. Once you've managed one of these basic carved turns (known as "railroad turns" ), you can try to make the transition into the next turn by shifting your weight across on to the other ski and tilting it.

As you start to carve railroad turns at a reasonable speed, you must keep a wide stance by keeping your outside leg extended away, out from under your body. If you allow your outside foot to get pushed in, so it's directly below your body, you may lose your balance and topple outwards, as centrifugal force tries to push your body towards the outside of the turn. As you keep that outside leg extended out at an angle, keep your hips dropped towards the inside of the turn, while the upper body remains upright. This is called "hip angulation" , and will put you in a strong position to resist that centrifugal force. Your outside leg should be fairly straight, with just a slight bend at the knee, so that you can use knee angulation to fine-tune your turns. (Hip angulation pro vides the power; knee angulation provides the control.)

Hip angulation will be easier to achieve if you keep your shoulders turned slightly away from the direction you're turning ( "counter-rotation" ). If you turn your shoulders in the same direction as you're turning your skis ("rotation"), strong hip angulation, and good carving, will be impossible.

At first, you'll probably find that your inside ski is just resting flat against the snow, with only 10-20% of your weight on it, acting as a "stabiliser". But as you gain confidence, you'll learn to edge the inside ski to the same angle of tilt as the outside ski. The inside leg will always have to be much more bent than the outside leg, and as you go around a turn, you'll learn how to "soften the outside leg" and bend it even further, allowing your hips to drop even closer to the ground. This is necessary in each turn, because the forces that you are trying to resist do not stay constant around the turn; in fact, they build up during the turn, reaching a maximum as you finish off the turn, cutting sharply across the hill.

To make the transition into the next turn, you need to utilise the springiness of your ski, to shoot your feet across, under your body, so that your legs end up extended out to the other side. In an instant, the new outside ski will bite and start to carve, and the new turn will be under way.

Carving becomes easier as you go faster, because your skis will respond quicker. But novice carvers should begin on flatter terrain and at lower speeds, before building up gradually, always taking care to maintain the correct body positions.

• Martin Bell is running ski courses for intermediate skiers this season in Vail & Breckenridge, Colorado. For more information, call 0170 8224080 or e-mail: vailresorts@clara.co.uk

 

Leave a Comment

Required fields are marked *

*

*